IMSAIGUY
UNITED STATES OF AMERICA • + Follow
Edit Project
Description
Zener Diode Tester
YouTube video will follow
Jumper settings for 5, 10, 15, and 20mA currents
Apr 16,2024
109 views
Zener Diode Tester
programmable currents to test zener diode
109
0
0
Published: Apr 16,2024
Download Gerber file 2
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
Topic
- Comments(0)
- Likes(0)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
View More
VOTING
0 votes
- 0 USER VOTES
0.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
More by IMSAIGUY
- Op-amp Test Board This is a two section board. two dual op-amps can be compared. Half of the device is used in a non-i...
- Zener Diode Tester YouTube video will followJumper settings for 5, 10, 15, and 20mA currents
- Dual and Quad OpAmp SImple Tester here is a video explaining the board
- NE5532 Headphone Amplifier YouTube video will followPopular op-amps are NE5532 JRC5532 NJM5532 you might consider JRC4556 fo...
- Linear Optocoupler youtube video will follow in a few weeksnote: pin one of the IC's are square pads, load correctly as...
- I2C 6 Digit Nixie Tube Display Here is YouTube video, note this is part 5 of a series. You might want to watch all five.
- Gyrator Board circuits from: https://sound-au.com/articles/gyrator-filters.htm
- Transistor Training PC Board youtube video will follow soonPlease don't ask for a BOM or schematic. The board IS the schematic. I...
- LCR Meter PCB Fixture Made for an LCR meter with kelvin 4 BNC fixtures. this is standard spacing of 22mm between connector...
- 8 LED SIP for Protoboard you can build it common cathode or common anode (put the LEDs in backwards)made for 0805 partsconnec...
- 2.4GHz Hairpin Bandpass Filter Designed with Keysight Genesys. If you order this board it must be fabricated with Rodgers 4003C 0.3...
- 2.45GHz YAGI Antenna Design This YAGI design is for 2.45GHz. if you order request: 1mm thick board, no solder mask, black silk s...
- Protoboard Power Connector this connects the power rails together, top and bottom, on a proto boardor just use extra wire for t...
- Analog Prototype board from old HP days Odd board for analog circuits. This is modeled after a board available in the HP stockroom when I wo...
- VNA SMA Calibration Standard Holder VNA SMA Calibration Standard HolderNice way to keep track of all you VNA cal standards
- SMA Thumbwheel Wrench Collar to be used on an SMA connector to provide a way to finger tighten. I have used PLA but I exp...
- Wire Grid Polarizer 5/5 mil wire grid polarizer. tested 1 GHz to 20 GHz
- Salen-Key Filters These filters are from the ARRL Handbook.Low PassHigh PassBand PassBand Reject (Notch)
You may also like
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
562 0 0 -
RF Control training board for students based on ESP32 C3
746 0 2 -
Aquarius+ Computer, Standard PCB
987 0 5 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
646 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
558 0 1 -
Nintendo Famicom HVC-001 Controller Shells
668 0 1 -
COMMODORE 128 DIAGNOSTIC REV.785260 KEYBOARD DONGLE
622 0 4