Mains Transformer Switched Adapter
I hate wiring mains transformers to terminal blocks in order to connect a power switch and fuse in series with it. This solves the issue, and allows two transformers to be switched off of the same switch! This should be good up to 3A on the primary, however, I would NOT recommend connecting a toroidal transformer (ONE) above 160VA. As this PCB is at mains potential, basic electrical safety should be followed. Keep fingers away from PCB when in operation and all spade terminal and connector connections should be INSULATED. When mounted in the project/device, it should really have a plastic box/cover over the top of the PCB to prevent accidental contact.
I will not be held liable or responsible for users of this PCB's negligence.
Mains Transformer Switched Adapter
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(0)
- Likes(0)
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Astro's Electronics Lab
- Headphone Adaptor for Power Amplifiers Add a headphone socket to any existing stereo amplifier that doesn't have one. This L-pad attenuator...
- Soft-Start Circuit for Toroidal Transformers WARNING: This project is connected to mains line voltage during its entire operation. This project s...
- AEL-50B Simple 50W Power Amplifier Need a simple power amplifier to drive a loudspeaker that doesn't require any messy set-ups to get g...
- +/-15V & +12V Regulated Power Supply This project allows you to have a +/-15V rail for a preamp and a +12V rail for powering some relays,...
- Amplifier Power Supply & DC Protection This unit will power two power amplifier modules up to 3A using a 300VA toroidal transformer. It wil...
- Dual-State Indicator This simple circuit is based around an astable multivibrator which is used to indicate two states fo...
- Discrete 24V Single Supply Stereo Preamplifier Input Indicator The LEDs mount on the top side passing through the front panel work, and the JST connector for the c...
- Discrete 24V Single Supply Stereo Preamplifier Simple discrete (3-transistor) stereo preamplifier with bass, treble, balance and volume. Also inclu...
- 0-15V Dual Channel Lab Power Supply Front Panel Front panel for the project to suit a Jaycar enclosure https://www.jaycar.com.au/pro-quality-instrum...
- ETI-480/AEL-480 50W Power Amplifier Module In March, 1977, ETI published a very popular project called the "ETI-480", with two versions offered...
- Mains Transformer Switched Adapter I hate wiring mains transformers to terminal blocks in order to connect a power switch and fuse in s...
- 0-15V 0.60mA-5A Adjustable Lab Power Supply Build two of these modules for a dual supply!There is a mis-print on the silkscreen for the bridge r...
- Mini 700mW Power Amplifier This little amplifier will deliver 700mW before clipping in to an 8 ohm load.Link to my YouTube vide...
- 1 Watt "Champ" Utility Amplifier Need a small utility amplifier to drive a speaker? This is the amp! Coined the "Champ", was original...
- AEL-480 Amplifier Power Supply & Muting Back in March, 1977, Electronics Today International (ETI) released a project called ETI-480. This w...
-
-
-
-
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
660 0 0 -
RF Control training board for students based on ESP32 C3
841 0 2