How to turn on lights with telegram and esp32 from anywhere in the world
In this tutorial we will see how to make a system that allows us to turn on lights with telegram, from anywhere in the world, just by typing a command. To do this a dual channel relay module will turn on two 110V/220V bulbs, the esp32 will connect to our Wifi network and by means of commands, to control the on or off of lights. We will send messages through the telegram messaging service, where the bot will respond to us when the light is turned on or off and we will also be able to know the status of each of them.
Circuit
Electronic components
Cables dupont
An ESP32
Features of the ESP32-T module
Connectivity
The ESP32 module has all the wiFi variants:
- 802.11 b/g/n/e/i/n
- Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management
This new version includes low-power Bluethoot connectivity
- Bluetooth v4.2 BR/EDR and BLE
- BLE Beacon
In addition, you can communicate using SPI, I2C, UART, MAC Ethernet, Host SD protocols
Microcontroller features
The CPU consists of a Tensilica LX6 Model SoC with the following features and memory
- Dual 32-bit core with 160MHz speed
- 448 kBytes ROM
- 520kByteS SRAM
Have 48 Pins
- 18 12-bit ADC
- 2 8-bit DAC
- 10 pin contact sensors
- 16 PWM
- 20 Digital inputs/outputs
Power and consumption modes
For proper operation of the ESP32 it is necessary to supply a voltage between 2.8V and 3.6V. The energy you consume depends on the mode of operation. It contains a mode, the Ultra Low Power Solution (ULP),in which basic tasks (ADC, PSTN…) continue to be performed in Sleep mode.
Two spotlights
A pcb
Gerber file
Pines macho
Dual-channel relay module
Features
- Card with 2-5V and 2-channel relays
- Tical current: 4mA
- Activation current: 2mA
- Working current: 65mA
- High Current Relay: AC250V 10A; DC30V 10A.
- Standard interface for microcontroller: Arduino, AVR, PIC, DSP, ARM, etc.
- PC817 on-board optocoupler with anti-jamming optical isolation capability
- Independent contact wiring, safe and reliable
- With screw holes for easy installation
- Size: 44.4×32.4mm
Pinout
Input Part:
- VCC: connect to positive power (depending on relay voltage range)
- GND: connect to negative power
- IN1: channel trigger pin 1 relay module (high level trigger)
- IN2: channel trigger pin 2 relay module (high level trigger)
Output Part:
- Normally open (NA): Normally open relay pin. NO pin is not connected to COM pin when relay is off. The pin does NOT connect to the COM pin when the relay is on.
- Pin común (COM): pin común del relé.
- Normally closed (NC): normally closed relay pin. The NC pin connects to the COM pin when the relay is off. The NC pin does not connect to the COM pin when the relay is on.
A plinth for the esp32
Source
#include <WiFi.h>
#include <WiFiClientSecure.h>
#include <UniversalTelegramBot.h>
// Reemplazar con los datos de tu red wifi
#define WIFI_SSID "Tu_red_wifi"
#define WIFI_PASSWORD "Tu_clave"
//Token de Telegram BOT se obtenienen desde Botfather en telegram
#define BOT_TOKEN "Tu_token"
const unsigned long tiempo = 1000; //tiempo medio entre mensajes de escaneo
WiFiClientSecure secured_client;
UniversalTelegramBot bot(BOT_TOKEN, secured_client);
unsigned long tiempoAnterior; //última vez que se realizó el análisis de mensajes
const int led12 = 12;
const int led14 = 14;
int estadoLed12 = 0;
int estadoLed14 = 0;
int inicio = 1;
String chat_id;
#define ID_Chat "tu_id_chat"//ID_Chat se obtiene de telegram
void mensajesNuevos(int numerosMensajes)
{
for (int i = 0; i < numerosMensajes; i++)
{
String chat_id = bot.messages[i].chat_id;
String text = bot.messages[i].text;
//////////Luz 1 en el pin 12//////
if (text == "Luz1on")
{
digitalWrite(led12, LOW); //
estadoLed12 = 1;
bot.sendMessage(chat_id, "Luz 1 encendida", "");
}
if (text == "Luz1off")
{
estadoLed12 = 0;
digitalWrite(led12, HIGH); //
bot.sendMessage(chat_id, "Luz 1 apagada", "");
}
//////////Luz 2 en el pin 14//////
if (text == "Luz2on")
{
digitalWrite(led14, LOW);
estadoLed14 = 1;
bot.sendMessage(chat_id, "Luz 2 encendida", "");
}
if (text == "Luz2off")
{
estadoLed14 = 0;
digitalWrite(led14, HIGH);
bot.sendMessage(chat_id, "Luz 2 apagada", "");
}
////////Estado de las luces ///////
if (text == "Estado")
{
////Estado luz 1////
if (estadoLed12)
{
bot.sendMessage(chat_id, "Luz 1 encendida", "");
}
else
{
bot.sendMessage(chat_id, "Luz 1 apagada", "");
}
////Estado luz 2////
if (estadoLed14)
{
bot.sendMessage(chat_id, "Luz 2 encendida", "");
}
else
{
bot.sendMessage(chat_id, "Luz 2 apagada", "");
}
}
if (text == "Ayuda")
{
String ayuda = "Bienvenido al sistema de control luces con Esp32, " ".\n";
ayuda += "Estas son tus opciones.\n\n";
ayuda += "Luz1on: para encender la Luz 1 \n";
ayuda += "Luz1off: para apagar la luz 1 \n";
ayuda += "Luz2on: para encender la Luz 2 \n";
ayuda += "Luz2off: para apagar la luz 2 \n";
ayuda += "Estado : devuelve el estado actual de las luces\n";
ayuda += "Ayuda: Imprime este menú \n";
ayuda += "Recuerda el sistema distingue entre mayuculas y minusculas \n";
bot.sendMessage(chat_id, ayuda, "");
}
}
}
void setup()
{
Serial.begin(115200);
pinMode(led12, OUTPUT); //inicializar pin 12 digital como salida.
pinMode(led14, OUTPUT); //inicializar pin 14 digital como salida.
digitalWrite(led12, HIGH); //
digitalWrite(led14, HIGH);
// Intenta conectarse a la red wifi
Serial.print("Conectando a la red ");
Serial.print(WIFI_SSID);
WiFi.begin(WIFI_SSID, WIFI_PASSWORD);
secured_client.setCACert(TELEGRAM_CERTIFICATE_ROOT); //Agregar certificado raíz para api.telegram.org
while (WiFi.status() != WL_CONNECTED)
{
Serial.print(".");
delay(500);
}
Serial.print("\nConectado a la red wifi. Dirección IP: ");
Serial.println(WiFi.localIP());
if(inicio == 1){
Serial.println("Sistema preparado");
bot.sendMessage(ID_Chat, "Sistema preparado!!!, escribe Ayuda para ver las opciones", "");//Enviamos un mensaje a telegram para informar que el sistema está listo
inicio = 0;
}
}
void loop()
{
//Verifica si hay datos nuevos en telegram cada 1 segundo
if (millis() - tiempoAnterior > tiempo)
{
int numerosMensajes = bot.getUpdates(bot.last_message_received + 1);
while (numerosMensajes)
{
Serial.println("Comando recibido");
mensajesNuevos(numerosMensajes);
numerosMensajes = bot.getUpdates(bot.last_message_received + 1);
}
tiempoAnterior = millis();
}
}
Download Library –> Universal-Arduino-Telegram-Bot-master
Create Bot on Telegram
In telegram we look for BotFather
We write /start and something similar to this will appear to us
Write /newbot
I will see the name of the bot, and we invent a name for our bot, it must be in the format ?usuario_bot?
We’ll get a token that we’re going to use in the source code
Now we’ll look for IDBot, and we’ll start it
We write /getid and it will give us user_id that we should place in the source code
How to turn on lights with telegram and esp32 from anywhere in the world
*PCBWay community is a shared platform and we are not responsible for any design issues.
- Comments(4)
- Likes(2)
- 1 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
-
10design
-
10usability
-
10creativity
-
10content
More by CarlosVolt Tutoriales
- How to make a water level meter with uln2803 In this tutorial we will see how to make a water level meter circuit with the built-in uln2803.The p...
- Emular mouse y teclado con arduino muy fácil En este tutorial, aprenderemos cómo utilizar un Arduino para emular tanto un mouse como un teclado e...
- Control of apc220 modules with smartphone and app Controlling APC220 modules using a smartphone and an app involves connecting via a serial USB adapte...
- Exploring the potential of the SI5351 module in electronic projects In this tutorial, you will dive into the depths of this amazing device and discover its limitless po...
- Gas leak detector alarm system with arduino nano In this tutorial we will see how to assemble a gas leak detector alarm system with arduino nano. We ...
- Build your own long-range weather station with Lora GPS anemometer module In this tutorial we will see how to create a weather station, for places where there is no internet ...
- Dual Synchronized Radio Frequency Control for Motor Lights and more In this tutorial we will see how to do a synchronized radio frequency control, since one control can...
- Object lifter with servo and Arduino Nano Does your waist or back hurt when you bend down? So this invention, it's for you and it can help you...
- 8-channel dual light ignition system, infrared and pushbuttons In this tutorial we will put together a dual light ignition system, since we can control the ignitio...
- How to turn on lights with telegram and esp32 from anywhere in the world In this tutorial we will see how to make a system that allows us to turn on lights with telegram, fr...
- Motion detector with light, esp32 and telegram notifications In this tutorial we will see how to make a motion detector system, with a PIR sensor, a relay module...
- Alcoholimeter with MQ3 sensor and arduino nano (Includes printed circuit) In this tutorial we will see how to make a breathalyzer, simple economical and easy to make. We’ll s...
- GPS tracker without cellular network with LORA module In this tutorial we will see how to make a tracker to GPS tracker, with LORA and Arduino module. We ...
- Build a meter with integrated circuit KA2284 KA2284 integrated circuit featuresHigh gain rectifier amplifier included (Gv = 26dB)Low radiation no...
-
BEAPER Nano (Beginner Electronics and Programming Educational Robot) for Arduino Nano ESP32
153 0 0 -
-
-
Open Source Very Large Stick - Freejoy & MMjoy2 breakout board
627 0 0 -
RF Control training board for students based on ESP32 C3
814 0 2 -
Aquarius+ Computer, Standard PCB
1069 0 7 -
KINETIC COASTERS with a TWIST! Laser or 3D Print some DIY Magic
683 0 1 -
RPI - 8 IO PLC With ATTiny85 Watch Dog
588 0 1