Manuel Caldeira
PORTUGAL • + Follow
Edit Project
Description
Full supply board for DIY Tube Tester
A DIY Tube Tester needs a lot of different power supplies to allow you to really test tubes correctly. You can set up these supplies independently, but a better solution is to build a single board that gives you all the voltages you need. This is it.
Using one single external transformer from an old tube radio, we supply the board with about 240 VAC (the transformer secondary voltage), and the heater AC voltage. What we get is:
- Two regulated High Voltage supplies, independently adjustable from 0 to 250VDC;
- A Negative Bias supply, adjustable from 0 to approximately -20VDC;
- A regulated 6.3VDC Heater supply;
- A Control voltage signal to activate relays or opto-couplers for the other elements in the circuit, like meters, etc.
Schematic and Layout
Oct 30,2022
3,589 views
Full supply board for DIY Tube Tester
Single board with 2 HV supplies (independently adjustable 0 to 250VDC), adjustable neg. bias supply, and regulated 6.3VDC heater supply.
3589
7
1
10.00 (1)
Published: Oct 30,2022
Download Gerber file 119
Purchase
Donation Received ($)
PCBWay Donate 10% cost To Author
*PCBWay community is a shared platform and we are not responsible for any design issues.
Copy this HTML into your page to embed a link to order this shared project
Copy
Under the
Attribution-ShareAlike (CC BY-SA)
License.
- Comments(1)
- Likes(7)
You can only upload 1 files in total. Each file cannot exceed 2MB. Supports JPG, JPEG, GIF, PNG, BMP
0 / 10000
Remove
It looks like you have not written anything. Please add a comment and try again.
View More
VOTING
1 votes
- 1 USER VOTES
10.00
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Design
1/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Usability
2/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Creativity
3/4
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
Content
4/4
-
10design
-
10usability
-
10creativity
-
10content
10.00
More by Manuel Caldeira
- Capacitor Foil-Side detector Capacitor Foil-Side detector. A self-contained device that gives you a visual indication of the foil...
- Inverse RIAA Network This Inverse RIAA Network lets you use your normal signal generator to test phono inputs of an ampli...
- Wax removal and alignment tool for tube radios Wax removal and alignment tool for tube radios
- Through-Hole_PCB_dial lamp LED boards_2024-01-20 PCBs to convert dial lamps to LEDs on vintage radios, Through-hole version
- PCB_dial lamp LED boards_SMD PCBs to convert dial lamps to LEDs on vintage radios, SMD version.
- Sony CRF-320 replacement gear set A set of 3 gears for the Sony crf-320 and crf-330 receivers, which are a common source of problems, ...
- test lead rack Cable test rack in resin
- test lead rack Cable test rack in PETG
- AC and DC voltage multiplier to extend the low voltage range of analogue multimeter and increase input impedance AC and DC voltage multiplier to extend the low voltage range of analogue multimeter and increase inp...
- PCB_Fetzer Valve smd_2023-10-09 An SMD version of a JFET Booster/Buffer that fits inside the guitar body, creating active pickups an...
- PCB_Fetzer Valve_2023-09-03 A Through-hole Buffer / Booster using a single JFET, that fits inside the guitar to provide active p...
- EO&N Op-Amp tester A simple op-amp tester that allows you to test single, dual and quad op-amps, using a single dual-co...
- Variable LM317 low voltage DC power supply A simple but useful pcb to make a small variable power supply using the LM317 i.c. with connections ...
- Selenium Rectifier and Filter Capacitor replacement PCB's - small size Selenium Rectifier and Filter Capacitor replacement PCB's - small size
- Selenium Rectifier and Filter Capacitor replacement PCB's - standard size Selenium Rectifier and Filter Capacitor replacement PCB's - standard size
- Decade Resistor Substitution Box A ver simple and cheap Decade Resistor Substitution Box for your workshop. I used 1% resistors, rate...
- EO&N CAPACITOR LEAKAGE TESTER A tester designed to test leakage in capacitors that also serves to reform electrolytic caps. High v...
- Opto-coupler or relay battery switcher A battery switcher using Opto-couplers or relays.
You may also like
-
IoT Indoor system with ESP32 to monitor Temperature, Humidity, Pressure, and Air Quality
338 0 2 -
Naruto Multi-color PCB printed with UV technology
135 2 1 -
-
-
-
-